How to use ratchet straps

How to use ratchet straps (best guide for you)

How to use ratchet straps– The ratchet belt is a load-bearing drawstring made of the polyester strap. They run through a buckle that allows you to loosen and tighten the belt so you can extend the belt until you pull it over your load, and then tighten the belt until there is enough tension to secure the load. Sometimes they ask us how to use a ratchet file and what a ratchet file is for.

A ratchet load strap can tie a load by placing it on the floor of a flatbed. It can also be used to tie a piece of cargo to the sides and secure it in a closed trailer. It can be attached to the side anchorage points of the flatbed, such as D-rings, and can also snap the anchorage points to the body floor for quick tightening!

Types of ratchet files according to use


All ratchet straps are made of polyester straps. Some ratchet straps strengthen the edges to prevent cuts and tears while maintaining their softness and flexibility. Thanks to this softness, they are ideal for transporting cargo that does not require much care, such as beehives, trees, or furniture.

Ratchet files work by passing a whole piece of cargo to secure it. Therefore, some large types of cargo, such as cars, are not compatible with a ratchet file. Basically, when you drive a car, you need special tow belts.

Latch belts have different ends, so you can use them to secure loads on trucks with different types of anchor points. The lashing belt with ratchet can be fitted with wire hooks, grip hooks, flat hooks, chains, or S-hooks. The final assembly you will need depends on the type of anchor points on the floor or walls of your truck.

Gain detailed knowledge of the types of ratchet files

When should you use a ratchet belt? Unlike a winch, a ratchet belt does not require the winches to be placed on the sides. But you don’t have to remove the reels! It winds and unwinds your polyester belt so that you can use it on some projects. For more information on the winch strap, see the details of the winch strap.

Compared to winch straps, the ratchet lashing strap can be secured regardless of any type of anchor point on the floor or side of your trailer. As a result, most flatbed trucks favor them. You can use it if you need to get a piece of cargo for transportation.

Before pulling, always make sure that your load does not exceed the ratchet load limit. If this happens, you can use multiple belts at short intervals to cut off the tension enough to load safely. Or it may be more appropriate to use a leather strap or G70 chain instead of a ratchet strap to secure the load.

How to use Ratchet Straps in 9 easy steps;


Below are 9 steps with photos and points; which will definitely help you when using a ratchet belt.

  • Step – 1. Use the release latch to open the ratchet
  • Til-op-ratchet handle
  • Use the release lever – also called the release lever – to hold the ratchet and shaft together at the same time with the open lock facing up.
  • The release latch is located in the center of the movable top of the ratchet.
  • In step 3, you will guide the belt through this hole.
  • Step 2. Close and turn the ratchet
  • close the ratchet
  • Close the ratchet to gain access to the axle assembly.
  • You can do this by pulling the release latch and turning the ratchet so that the gears (point wheels) point upwards.
  • Step 3. Pass the belt through the open lock
  • step-3-take-ratchet-pod
  • Remove the open lock under the ratchet (mandrel) and then tie the free end of the belt by bringing the belt under the ratchet and pushing it up over the open lock.
  • Wrap it around the shaft and then return the belt to the same hole you used before. The belt should be placed straight and the other half of the belt should overlap on the opposite side of the ratchet.
  • Step 4. Secure the terminals
  • step-4-take-attach-hook
  • Attach the ends at both ends – flat hook, chain anchor, etc. – to the belt and place them in place.
  • Step – 5. Pull the free end of the strap
  • step-5 ratchet belt
  • Pull on the free end of the belt until it hardens so that there is no play between the two ends.
  • If there is too much strap left from the mandrel, you risk jamming the ratchet when you start tightening.
  • Remember: you can always grind it later, don’t worry about length!
  • Step – 6. Hold the ratchet
  • Ratchet pump
  • Pump the ratchet handle to remove the remaining play and tighten the belt. If you do, you should see a belt around the axle. Once you feel firm and safe, stop creaking.
  • Be careful not to be too tight! Excessive pressure and tension can damage the load if you tear / cut the belt.
  • If it does not fit between the belt and the load, this is a good sign that it is too tight and you must loosen the belt.
  • You need to find a happy center among the safe, but not too tight.
  • Step – 7. Close and close the ratchet handle
  • step-7-close-ratchet-handle
  • When the belt is finally fully tightened, close the ratchet completely.
  • Secure the belt in place. You can do this by turning the ratchet back to the closed position and keeping it closed until you hear it close.
  • If you do not hear a click, tighten the strap and buckle to ensure safety. If it comes loose, find and then use another ratchet file – it can be a mistake!
  • Step – 8. Pull and hold the release handle
  • Pull and hold the release handle
  • To remove the ratchet file, remove and hold the release lever. The release tab should be easily accessible above the ratchet.
  • This deactivates the ratchet function, releasing the lock and opening the ratchet handle.
  • Then the strap is removed and you can easily pull it into the axle lock.
  • Open the ratchet so that it lies flat and remove the belt from the ratchet handle. Step – 9. After use; Inspection, packaging, storage
  • step-9-pack-ratchet-with-rubber
  • When you have finished using the ratchet strap, wrap it and tie it with a rubber band.
  • Once the belt is secured, place the belt and ratchet together in a dry suitcase or bag.
  • Inspect the ratchet, end piece and belt itself for tears, damage, or elongation / deformation. If you see damage, you know how to replace the truck accessories for further work!
  • Read the full article on ratchet file care and maintenance tips

Quality ratchet straps myth


At Mytee, we offer incredible power options, including the Kinedyne K-force Ratchet. This ratchet strap has a unique payload limit of 4,000 pounds: 20% stronger than the next strongest ratchet strap on the market.

Whatever strength or strap length you need, the Mytee has a tip line that fits your truck.

All our ratchet belts are of high quality and cost less than anywhere else. These ratchet straps keep your cargo safe so you can transport it safely and cheaper.

To better understand how to use a ratchet strap, watch this video. It is important to follow the instructions in this article carefully to ensure that the transport is correct and safe. The ratchet conveyor belt helps speed up the transport of loads of various sizes and gives you confidence in handling the load when you are on the go! However, you must always secure it properly and also check the ratchet and belt for damage before use.

Read also about Ratchet Straps

Frequently asked questions about using ratchets

  1. How can you use a ratchet file on a truck or van?
    Once your load is secured to or from your truck, place the ratchet strap over the load and hang the ends on the side of the body or on the lashing rings / anchor points / grooves on the fan wall. Install the belt until it changes and make sure it is secured. Secure the belt firmly. If you use the right number of straps needed to keep the load stable, you should be able to safely carry the load in your truck or van with ratchet carrying straps!
  2. How to connect two ratchet straps?
    It is possible to connect two E-Track end-to-end ratchet belts. However, they must be designed for this. However, you cannot have a long ratchet file, so it is best for transporting very small and flat loads.
  3. How often do you change the ratchet belt?
    If you take good care of your ratchets and load belt, the ratchet belt should last you 2 to 4 years. Do not use the ratchet file if there is obvious abrasive damage, breakage, or any hardware deformation of the ratchet itself. After each work, check the belts and ratchets and, if you notice injuries, replace the truck accessories!
  4. How can you use a ratchet belt for kayaking?
    Using a ratchet strap and cam strap are great ways to tie kayaks high in the back of a car or truck. Make sure your kayak is centered and runs parallel to the top of the car. Take a ratchet strap and position it so that it lies on the side of the kayak a few inches above or on the side of the car’s crossmembers. Take the other end over the kayak, remove the end of the belt and pass it under the crossmembers of the car so that the belt does not tear.
    Repeat this process for the other straps you plan to use, and then snap the straps until the kayak snaps – but not too tight! Excessive stress can damage the kayak.
  5. How to use a ratchet strap on a roof rack? When things are strapped to the roof of the car, ratchet straps are a great choice to ensure that your load does not get wet and do not fly on the road. If your car already has a roof rack, ratchet strap

Leave a Comment

Your email address will not be published.